In-house laundry equipment: matching washers, dryers and ironers to the linen load
Size your hotel laundry from your own peak-day linen load, not the supplier's catalogue. Learn to match washer, dryer and ironer throughput in kilograms per hour to avoid bottlenecks.
Contents
Key takeaways
- Size a hotel laundry from kilograms of soiled linen on the peak changeover day, not from a machine's rated kilograms per cycle.
- Compare washers, dryers and ironers in one unit, kilograms per hour, because drum size says nothing about throughput.
- Whichever of the three machines has the lowest hourly throughput sets the laundry's daily ceiling.
- Par stock and turnaround time decide whether a busy day is a scheduling problem or a capacity problem.
- Outsourcing removes capital, space and staff but adds transport lead time, so the linen par stock has to rise.
In-house laundry equipment is sized from your own linen load: weigh what one room-night puts into the wash, add food and beverage, spa and uniform linen, then size for the peak day, not the average. Washer, dryer and ironer must match in kilograms per hour, and the slowest machine sets the laundry's capacity.
A bigger washer arrives, and the laundry still finishes late on changeover days. The machine was rarely the constraint: nobody had measured the load, the dryer and the ironer were never matched to it, and nobody had counted the hours the room actually runs. Hotel laundry equipment selection starts with your own numbers, not the supplier's catalogue. After reading this you will be able to turn your occupancy and linen sets into a single figure, kilograms per hour, and put it in front of any supplier.
How much laundry does a hotel produce in a day?
Multiply the linen one room-night puts into the wash by the rooms you actually sell, then add the linen from food and beverage, spa, pool and staff. The result, in kilograms per day, is the number a supplier needs.
Define the linen set before you count anything. The set is the bed linen, duvet cover, pillowcases, bath and hand towels and bath mat that one room-night sends to the wash. A three-night stay does not produce three full sets: it produces one departure set plus the towel changes your own policy asks for. Write the policy down before you weigh, because the towel rule changes the total more than most people expect.
Weigh instead of estimating. Take one full soiled set to a platform scale, repeat for a double room and a suite, and write the figures down. Supplier tables describe a generic hotel, not your linen. If you need a reminder of what belongs in the set, see the working list of hotel linen items, sizes and terms.
Record two weights per set: dry, and as it comes off the trolley. Machines are rated in dry kilograms, but the laundry weighs damp linen, and the gap between the two numbers explains most arguments about capacity. For example, a set that weighs 3.5 kilograms dry can weigh noticeably more damp, and staff will report the damp figure as the load.
Then add the streams that are not rooms: restaurant tablecloths and napkins counted by covers, kitchen cloths, bar towels, spa, pool and gym towels, staff uniforms and cleaning cloths. Each has its own daily count and its own weight. Convert to a daily figure with your own occupancy: occupied rooms per day from the hotel system, multiplied by the set weight, plus the other streams. Keep the answer both as kilograms per day and as kilograms per occupied room-night, so you can re-run it when occupancy moves.
Write the arithmetic on one page and keep it. Every later decision, machine size, staffing, par stock and outsourcing, is checked against that page. If laundry vocabulary is new to the team, the plain-language guide to laundry terms covers load, cycle, extractor and ironer.
Checklist
- Weigh one single room set, dry and damp
- Weigh one double room set, dry and damp
- Weigh one suite set, dry and damp
- Weigh one restaurant cover's cloth, tablecloth and napkins together
- Weigh one spa or pool towel set
- Weigh one staff uniform set
- Weigh one batch of kitchen cloths
- For each, record how many the hotel uses on a normal day
Why does the average day give you the wrong machine size?
Because soiled linen cannot wait: linen that arrives on a changeover day has to be back in a room within the par stock you own, so the peak day sets the requirement and the average day only sets the running cost.
The peak day is the day with the most departures and arrivals inside the same working hours, not the night with the highest occupancy. A full house with few departures sends far less linen to the wash than a changeover day at a lower occupancy. Every departure produces a full set; every stay-over produces only the towels your policy replaces.
Par stock sets your buffer. Count how many complete sets you own per room across three places: in use in the room, in the wash or the store, and in transit. The number of sets decides how many days a peak can be spread over. Two sets per room means the laundry must finish within one day; four sets buys you breathing room.
Map the day before you size the machines. Check-out linen arrives in a burst between check-out time and mid-afternoon, so the laundry's usable hours are shorter than the shift on paper. A room that opens at 08:00 and receives its first heavy soiled loads at 11:00 has lost three hours already.
Build the peak-day figure as a small table. Group check-outs, weddings and event days create spikes that an average hides completely, so ask the front office for the last year's busiest weeks and use those dates. Then put the peak-day figure and the required kilograms per hour into the request for quotation, so every supplier prices the same duty.
| Input | Where the number comes from | Example (for example only) |
|---|---|---|
| Sellable rooms | Room list | 120 |
| Occupied rooms, peak day | Busiest changeover day in the system | 108 |
| Departures that day | Departure list | 74 |
| Dry kg per room set | Your own scale | 3.5 |
| Room linen kg | Occupied rooms × set weight | 378 |
| Food and beverage linen kg | Covers × cloth weight | 45 |
| Spa, pool, gym towels kg | Towel count × weight | 30 |
| Uniforms and cleaning cloths kg | Pieces × weight | 17 |
| Peak-day total | Sum | 470 |
| Usable laundry hours | Shift plan minus breaks | 8 |
| Required kg per hour | Total ÷ hours | 59 |
How do washers, dryers and ironers balance against each other?
Match them in kilograms per hour, not in drum size: each machine's hourly throughput is its dry load multiplied by the cycles it completes in an hour, and the machine with the lowest figure sets the laundry's ceiling.
Washer throughput is rated dry capacity per cycle, multiplied by 60 and divided by the total cycle minutes, including loading, washing, rinsing, extracting and unloading. For example, a machine rated at 25 kilograms that completes a full cycle in 60 minutes delivers about 25 kilograms an hour. The same machine with a 75-minute cycle delivers 20.
Dryer throughput is usually the lower number, because dryer drums are often smaller than washer drums and drying takes longer than washing. A better extract shortens drying time, so extraction quality is part of the dryer decision. This is why the washer and the dryer are bought together, not separately.
Ironer throughput is measured in items or meters per minute, and it is limited by the people feeding it. Flatwork goes through the ironer: sheets, duvet covers and tablecloths. Terry does not, so towels depend on the dryer and the folder instead. When you compare offers, convert the ironer's meters per minute into kilograms of flatwork per hour so all three machines speak the same unit.
One large machine against several small ones is a trade-off, not a ranking. Small machines give redundancy and fit a low season; a large machine gives throughput but wants a full load to run well, which is awkward in a quiet month. A machine down for a day also means a different share of capacity lost: one of three small machines is a third, the only large machine is everything.
Separate the streams. Guest linen, kitchen cloths and cleaning cloths go through separate machines or strictly separate cycles, and the hotel's own hygiene plan should say which. A barrier machine, with a loading side and an unloading side in different rooms, is one way to enforce the separation physically. Leave headroom for rewash: stained or damaged pieces come back through the line, so set the allowance from your own stain rate rather than a rule of thumb borrowed from someone else.
Key pointOne unit for all three machines
Kilograms per hour equals dry load per cycle multiplied by 60, divided by total cycle minutes including loading and unloading. Compare washer, dryer and ironer on that figure. The lowest number is the laundry's ceiling, whatever the drum sizes say.
What do you check about space, drainage and ventilation before you buy?
Check the room around the machines before the machines: floor loading, drainage, water supply, heat source, air for the dryers and a route in for delivery decide more installations than the equipment does.
Ask for the supplier's layout drawing with clearances: machine dimensions plus door swing, the loading side, service access at the back and a turning circle for the trolley. A machine that fits but cannot be serviced is a machine that stops. Lay the room out in one direction: soiled linen in at one end, clean linen out at the other, with no crossing. A laundry arranged as a loop puts clean linen back beside soiled linen.
Drainage: check gully position and capacity, fit lint traps, and confirm with the building's mechanical engineer and your local water and sewerage authority what may be discharged and at what temperature. Water and heat: measure supply pressure and flow, confirm hot water capacity, and settle whether the machines are heated by steam, gas or electricity. Steam means boiler capacity and a steam line, not just a connection.
Ventilation: dryers need make-up air and a short, accessible duct route to outside. Lint is a fire load, so the duct run is cleaned on a written schedule and never boxed in. Floor and structure: loading confirmed by a structural engineer, waterproofing, a slope to the drain, and vibration isolation where guest rooms sit above or beside the room. Chemicals and access: a locked, ventilated store with dosing equipment and safety data sheets on file, plus door widths and corridor turns that let a machine in now and out again in ten years. Since dryers and ironers are major energy users, what to check before investing in energy management belongs on the same reading list.
Checklist
- Floor loading confirmed by a structural engineer
- Drain position, capacity and lint trap
- Hot and cold water pressure and flow measured
- Steam, gas or electrical supply confirmed against boiler or panel capacity
- Duct route to outside agreed with the building owner
- Make-up air for the dryers
- Floor waterproofing and slope to the drain
- Locked, ventilated chemical store
- Delivery route, door widths and turning space
- Noise and vibration checked at the nearest guest room
What should you ask a supplier about service and spare parts?
Ask for the response time, the parts held in the country and the training in writing, because a laundry that stops on a changeover day costs more than the machine did.
Response time and who attends: the supplier's own technician or a subcontractor, the nearest service point, and what happens outside working hours. Get the number of hours, not the phrase "as soon as possible". Spare parts: which parts are held locally, which are consumables you should stock yourself, such as belts, seals, door gaskets and lint filters, and how long a model stays supported after it is discontinued.
Warranty: what it covers, what voids it, and how a claim is handled. Water hardness, unauthorized repair and chemical damage are the usual exclusions, so check them against your own water. Commissioning: who installs, who connects water, drain, steam and power, and who signs off the first week of running. The boundary between the supplier and your mechanical contractor is where installations go wrong.
Training: the hotel's laundry staff trained on loading weights, cycle selection, dosing and daily cleaning, with a written operating routine left behind so the knowledge stays when a person leaves. Documentation: manuals, an error code list and wiring diagrams in a language the team reads, plus remote diagnostics or a technician reachable during a shift. Ask for a site visit to a laundry running the same model, so you can watch it loaded and unloaded rather than see it in a showroom.
TipPut these in the purchase contract
Written response time and the named service point; the spare parts held locally and the consumables list; what voids the warranty; who installs and who connects water, drain, steam and power; staff training and a written operating routine; manuals and an error code list in a language the team reads; how long a discontinued model stays supported.
Outsource or run the laundry in-house: what decides it?
Compare the whole system, not the cost per kilogram: outsourcing removes capital, space and staff but adds transport lead time, so the par stock and the quality control work move to you either way.
In-house buys control: turnaround on a changeover day is yours, there is no transport, and linen life sits under your own cycles and dosing. You pay for it in capital, space, staff across seven days and the chemical and wastewater questions. Outsourcing buys simplicity: no capital, no laundry rota, no chemical handling, and a bill per kilogram you can budget. You pay for it in lead time, because linen travels and comes back on someone else's schedule.
Par stock follows the choice. An outsourced laundry needs enough sets to cover the transport cycle, so you own more linen, and loss and damage become a monthly reconciliation with a third party. Put a value on the square meters too: the laundry's floor area is rooms, a spa or a store in most buildings, and that alternative use belongs in the comparison.
Consider the hybrid: flatwork in-house with terry outsourced, or the reverse. Treat dry cleaning as its own decision, usually a separate contract, and do not let it drive the whole comparison. The decision rule: high year-round occupancy, space already available and a par stock you can fund favor in-house. A short season, a small building and no suitable room favor outsourcing. Write the comparison with your own figures and revisit it when occupancy, rooms or the restaurant change.
| Area | In-house | Outsourced |
|---|---|---|
| Capital | Hotel buys machines | None |
| Space | Laundry room held | Freed for another use |
| Staffing | Team across seven days | None in laundry |
| Par stock | Lower | Higher, covers transport cycle |
| Changeover turnaround | Same day | Supplier's schedule |
| Quality control | Own cycles and dosing | Receiving checks |
| Loss and damage | Internal count | Monthly reconciliation |
| Water, energy, chemicals | Hotel pays and handles | In the price |
| Wastewater | Hotel's question | Supplier's |
| Low-season flexibility | Machines idle | Bill follows volume |
How do you keep the equipment matched to the load after opening?
Measure the load again every season and keep a daily log of kilograms washed, hours run, rewash and downtime, so the next purchase is decided by your own figures.
Keep one line a day: kilograms washed, hours the laundry ran, kilograms rewash, machines down and for how long, chemical consumption, and a note on stains or damage. Compare the log against the peak-day figure you designed for. When occupancy grows, the first constraint to appear is the machine with the lowest hourly throughput, and the log shows which one it is.
Review par stock before you buy capacity. If the laundry finishes late, more sets may solve it; if it runs all day at full load, the constraint is real. Plan preventive maintenance in the low season: descaling according to your water hardness, drum and door seals, lint duct cleaning and dosing calibration. Hold the supplier to the response time you wrote into the contract by recording every call-out and its duration.
Re-run the sizing when the building changes: extra rooms, a spa, a new restaurant or a bigger event space all add linen that the original calculation never saw. The daily log also feeds the wider stock count; see the year-end inventory count for stores, linen and equipment for how the two fit together.
NoteA one-page daily laundry log
Date; kilograms washed; hours the laundry ran; kilograms rewash; machines down and for how long; chemical consumption; notes on stains or damage. One line a day is enough to show when the laundry stops matching the load.
What to do next
Weigh one soiled room set and count the departures on your busiest changeover day this week. Those two numbers turn the whole article into a single figure, kilograms per hour, that you can put in front of every supplier, and they decide the space, the service contract and the in-house or outsourced question that follow.
Frequently asked questions
How many kilograms of laundry does one hotel room produce per night?
There is no figure that transfers between hotels, because the set differs by room type and the stay pattern differs by hotel. The reliable method is to weigh your own single, double and suite sets, dry and damp, multiply by the rooms you actually occupy, then add food and beverage, spa, pool and uniform linen. Keep the result as kilograms per occupied room-night so it can be re-run when occupancy or linen changes.
How many hours a day should a hotel laundry run?
Capacity is hourly throughput multiplied by usable hours, so the hours and the machines are one decision. One shift may cover the average day and fail on the peak changeover day. The choice is between a second shift, more par stock to spread the peak, or more machine capacity, and the peak-day figure tells you which is cheapest for your building.
Do kitchen cloths and guest linen need separate machines?
The separation is a hygiene decision the hotel writes into its own hygiene plan and laundry procedure, not something a machine decides. Separate machines are the clearest way to enforce it, strictly separate cycles and storage are the alternative, and a barrier machine is a third option. Agree the rule with the team responsible for food safety and put it in writing for the laundry staff.
Is an in-house laundry cheaper than outsourcing?
It depends on volume, the value of the space, staffing and how much linen you must own. In-house turns a per-kilogram bill into capital, labor, water, energy and chemicals, and it gives you control of turnaround. Outsourcing removes those costs but adds transport lead time and usually more par stock, so compare the two with your own peak-day figure and your own space, not with a supplier's summary.
What size ironer does a hotel need?
Size the ironer on flatwork items per peak hour, not on room count. Its speed in meters per minute, times 60, divided by the item length in meters, gives items per hour, and the people feeding it usually set the real limit. Towels do not pass through the ironer, so for terry the dryer and the folder matter more than the ironer's width.


